Serving Long Beach, CA & Surrounding Coastal Communities Fast Phone Response
Call for Service: +1 (562) 271-5637

Navien Tankless Error Codes Decoded: How to Fix E003, E011, E016 & E110

When your Navien tankless water heater flashes an error code on its digital display, it automatically locks out for safety to prevent damage or hazardous conditions. Understanding what each diagnostic error code means—and knowing which simple checks are homeowner-safe versus those requiring a licensed pro—will get your hot water back quickly.

Navien tankless water heater digital control panel showing diagnostic error code
Navien tankless water heater digital control panel showing diagnostic error code
Key Takeaways

Quick Diagnostic Guide: Most Common Navien Error Codes

The four most frequent Navien error codes in Long Beach are E003 (Ignition Failure), E011 (Gas Supply/Pressure Fault), E016 (Heat Exchanger Overheating due to Scale), and E110 (Exhaust Vent Blockage). Many ignition and venting errors stem from simple issues like closed gas shutoff valves, clogged intake screen filters, or spider webs in outdoor vent terminals.

  • E003 / E011: Check that yellow gas cock is parallel to the pipe and gas meter is active.
  • E016: Water heater is overheating; almost always caused by hard water scale buildup requiring descaling.
  • E110: Intake air filter is clogged with lint/dust or PVC vent terminal is obstructed outdoors.
Safety Warning: If you smell natural gas (rotten eggs) or hear violent backfiring, do NOT press reset. Shut off the gas valve and call our 24/7 Long Beach repair hotline at (562) 271-5637.

Understanding the Navien Digital Control Interface

Modern Navien condensing units (including the NPE-A2, NPE-S2, and legacy NPE-A series) feature sophisticated microprocessor controllers that constantly monitor combustion airflow, gas pressure, flame ionization, thermistor temperatures, and water flow rates.

When a sensor detects an out-of-parameter reading, the front panel LCD illuminates in red with a three-digit code prefixed by the letter 'E' (Error). The unit disables the burner to prevent catastrophic component failure or carbon monoxide hazards.

Master Navien Error Code Diagnostic Table

Use this quick reference table to diagnose the root cause of your Navien error code:

Error Code Failure Description Probable Root Causes Recommended Action
E003 Ignition Failure Closed gas cock; low gas inlet pressure; dirty flame rod; bad igniter electrode. Verify gas valve is open; clean flame rod; call technician for gas pressure test.
E011 Flame Outage During Operation Fluctuating gas supply; strong winds blowing into terminal; gas meter regulator freeze/lockup. Check exterior vent terminations; inspect gas meter; professional gas manometer test.
E016 Heat Exchanger Overheating Hard water scale insulation; clogged inlet water filter; restricted recirculating loop. Perform full system descaling flush; clean cold water inlet screen filter.
E029 Abnormal Flue Gas Temperature Scale in primary heat exchanger preventing heat absorption; combustion fan failure. Immediate professional descaling; inspect flue gas thermistor.
E046 Heat Exchanger Thermistor Open Loose wiring harness; damaged thermistor sensor; water leak onto terminal board. Inspect wiring connections; replace faulty high-limit thermistor.
E110 Air Pressure / Exhaust Obstruction Clogged air intake filter; bird nest or spider webs in PVC termination; fan motor failure. Clean internal air intake filter; inspect outdoor vent pipes for obstructions.

Error E003 & E011: Ignition & Gas Supply Problems

Error E003 indicates that the unit sparked but failed to establish a stable flame signal within 5 seconds. Error E011 indicates that flame was established but unexpectedly dropped out during operation.

Here is how to safely troubleshoot these errors:

  1. Verify Main Gas Supply: Confirm that the yellow-handled gas shutoff valve directly beneath the Navien unit is parallel to the pipe (OPEN position). If other gas appliances (stove, furnace) are also not working, check the main SoCalGas meter outside.
  2. Check for Condensate Trap Backlog: Navien condensing units generate slightly acidic condensate water that must drain continuously. If the condensate drain line or internal trap is kinked or clogged, water backs up into the exhaust collector, blocking the burner.
  3. Dirty Flame Detection Rod: Over years of operation, microscopic carbon oxidation coats the flame rod. The microamp electrical signal can no longer travel to ground, causing the computer to believe there is no flame. A technician cleans this with fine emery cloth.

Error E016: Heat Exchanger Overheating & Hard Water Scale

In Long Beach, E016 is by far the most common code on units that are 2 to 5 years old. This code triggers when the heat exchanger high-limit thermistor registers water temperatures exceeding safe engineering limits.

Because Long Beach tap water contains 13 to 17 grains of calcium hardness, calcium carbonate bakes onto the internal heat exchanger walls. This scale acts like ceramic insulation. The gas burner fires at full 199,000 BTU blast, but the heat cannot transfer into the water through the scale layer. The metal overheats, and the high-limit sensor trips E016 to prevent the heat exchanger from melting or cracking.

The Fix: A comprehensive 45-minute descaling flush using a submersible pump, 4 gallons of food-grade virgin white vinegar or Flow-Aide descaler, circulating through the dedicated service isolation valves.

How to Clean the Navien Air Intake Filter (Safe DIY Step)

If your unit displays E110, the internal air filter may simply be choked with dust, dryer lint, or pet hair:

  • Turn off the electrical power switch on the bottom of the unit or unplug it.
  • Remove the four front cover screws and lift off the front panel.
  • Locate the white plastic intake filter housing at the top left of the cabinet.
  • Unclip the plastic bracket, slide out the mesh filter screen, and rinse it under warm tap water.
  • Dry completely, reinstall the filter, replace the front panel, and power the unit back on.

When DIY Troubleshooting Stops

Never attempt to adjust the internal gas air-ratio manifold, disassemble the sealed combustion fan, or bypass high-limit safety switches. High-efficiency gas appliances require calibrated electronic manometers and flue gas analyzers to operate safely without producing dangerous carbon monoxide.

Frequently Asked Questions

Press the Power button on the front control panel to turn the unit OFF. Wait 30 seconds, then press the Power button to turn it back ON. If the error immediately reappears, do not keep resetting; the safety lockout is protecting the appliance.

Frequent E016 errors indicate severe hard water scale accumulation. Long Beach's water hardness (220–300 mg/L) rapidly scales internal tubes. Installing a cartridge-based polyphosphate scale inhibitor or whole-home water softener prevents this.

Yes. Freezing or near-freezing coastal winter winds can freeze uninsulated exterior condensate drain lines, backing up water into the combustion chamber and throwing error E110 or E003.

Immediately evacuate the area, do not operate light switches or phones nearby, shut off the gas valve if accessible, and call SoCalGas or 911 from a safe distance.

Standard diagnostic visits in Long Beach range between $99 and $189, with upfront pricing provided before any part replacement or descaling service begins.

Fast Phone Assistance

Need Water Heater Help in Long Beach?

Don't ignore leaks, strange noises, or sudden pilot shutdowns. Speak directly with a local specialist to discuss your water heater symptoms and schedule fast service.

Call (562) 271-5637 • 24/7 Fast Dispatch